Jessica (2008-08-19,
Yahoo!) Straight Line
What's the cartesian equation of the line through (-8,9) and (10,-3) ?
For a point (x,y) on that line, the vector
from (-8,9) to (x,y) is proportional to the vector from (-8,9) to (10,-3).
The relevant determinant vanishes:
10 + 8 -3 - 9
x + 8 y - 9
= 0
Thus, 18(y-9) + 12(x+8) = 0. which boils down to the equation of the line:
2 x + 3 y = 11
(2004-06-23) Confocal Conics
Ellipses and hyperbolae sharing the same foci.
Ivory's Theorem:
In a curvilinear quadrangle formed by two pairs of confocal conics, the diagonals are equal.
The conic sections were named by Apollonius of Perga (262-190 BC).
Dandelin spheres (1822)
are due to
(Pierre) Germinal Dandelin (1794-1847; X1813)
partial credit also goes to
Adolphe Quételet (1796-1874)
Hamilton (1805-1865)
remarked that a Dandelin sphere touches the cone in a plane containing a directrix.
In 1829,
Pierce Morton (1803-1859)
used Dandelin spheres to prove the focus-directrix property of conics.
What's the length of the spiral from a vinyl record (or a paper towel roll)
as a function of the distance to the center?
A spiral of Archimedes may be described as the trajectory of a point
which moves at constant speed along a spoke of a wheel rotating at a constant rate.
As the distance (r) from the center to a point on the spiral is proportional to the angle
(q) between the spoke and some fixed line,
the polar equation is:
r = a q
The angle q (expressed in radians) increases by
2p with each turn.
Therefore, the quantity 2pa is
the thickness of the paper on a roll,
or the distance between adjacent parts of the groove on a vinyl record.
When the polar coordinates (r,q) of a point
change minutely by (dr,dq),
that point travels a minute distance ds, given by the following
relation (obtained from the Pythagorean theorem,
since a smooth curve looks straight at small enough scales):
(ds)2 =
(dr)2 + (r dq)2
In the case of Archimedes' spiral, this means:
ds = a (1 + q 2 )½
dq.
The length (s) of the spiral is obtained by
integrating this:
s
=
½ aq
Ö
1 + q2
+ ½ a ln (
Ö
1 + q2
+ q )
=
½ r
Ö
1 + (r/a)2
+ ½ a ln (
Ö
1 + (r/a)2
+ r/a )
For a roll of paper of diameter 2r1 with a core of diameter 2r0
the total length is simply
s(r1)-s(r0).
[Recal that 2pa is the thickness of the paper.]
A Simple Approximation:
The exact formula above is an overkill for estimating
the length of paper on a roll.
Instead, you may consider that, if the paper is very thin compared to the
diameter of the core, the surface area of the roll's cross section divided
by the thickness (e = 2pa)
of the paper gives you its length, namely:
s »
(r12 - r02 ) / 2a
= p
(r12 - r02 ) / e
This approximation is just the leading term of the above exact formula.
For a 65 ft roll of paper towels, 2r1 = 5" and
2r0 = 1.75".
The thickness of the paper, measured with a caliper, is 0.01".
Plugging this into the formula yields a length of about 144 ft,
which is more than twice the actual value. What's wrong?
A paper towel normally has features (fluffiness, waviness, embossment)
which make the caliper measurement of a single sheet greatly underestimate the effective
thickness of the material in a stack or a roll.
By working the formula backwards, the above numbers would indicate that the paper
material has an effective thickness of about 0.022".
This could be obtained directly by counting the number N of turns it takes for the diameter
of the roll to decrease by x inches (the effective thickness of the stuff
would then be x / 2N).
If you insist on using a caliper,
you may reduce by a factor of N the large error obtained for a single
sheet, simply by using the caliper (without squeezing) on a stack of N sheets...
If a roll of paper towels of the type quoted above has a diameter D (in inches)
then its footage is approximately:
( D 2 - 3.06 ) 2.96 ft
(2008-03-29) Catenary or chainette The shape of a chain under its own weight :
y + a = a ch(x/a)
A thin uniform rope without any rigidity is
traditionally called a chain
(in Latin: catena).
The lack of any force sideways means
there's just a tangential tension.
Let's characterize the shape (catenary)
of a chain under its own weight:
Let j be the inclination
of the chain (i.e., the angle its tangent makes with the horizontal x-axis)
at a given curvilinear abscissa s.
The tension pulling on the left part of the chain has magnitude
F and coordinates
(F cos j, F sin j).
For a positive displacement ds along the rope, the infinitesimal
increase of the vertical component is balanced by the weight of the corresponding
piece of rope (we assume the mass per unit of length to
be a constant m ) :
d ( F sin j )
=
g m ds
As the horizontal component of the tension is a constant:
F = K / cos j
d ( K tan j )
=
g m ds
A Cartesian relation is readily obtained by using
y' = dy/dx = tan j
K d(y' ) =
g m
( 1 + (y' ) 2 ) ½ dx
This is integrated as a simple quadrature,
by considering x as function of
y' :
x = xo +
a Argsh ( y' )
[ introducing a = K/gm ]
Conversely, y' = sh [(x-xo )/a]. Therefore,
by integration:
y = yo + a ch [(x-xo )/a]
Thus, if we use the apex of the curve as origin of the coordinates, we have:
y = a ch (x/a)
- a =
2 a sh2 (x/2a)
The curvilinear abscissa is simply :
s = a sh (x/a)
= a tan j
For a plane curve, such a relation between the
arclength s and the inclination
j goes by the name of
Whewell equation.
It can be used to derive the so-called
intrinsic Cesàro equation which relates the (signed)
radius of curvature
R = ds/dj
and the arclength s. In the case of the catenary,
we have:
R = ds/dj =
a ( 1 +
tan2 j ) =
a + s2/a
So, the parameter a
is the radius of curvature at the catenary's apex (s=0).
Galileo (1564-1642)
thought that a chain under its own weight would take on a parabolic shape, which
Jungius
(1587-1657) disproved.
The latin name catenaria was coined by
Huygens in 1690
(in a letter to Leibniz).
This was immediatly translayed as "chainette" in French.
In English, the locution "catenarian curve" was used at first.
Thomas Jefferson introduced the word catenary a century later
(1788).
The above equations for a catenary were first derived in 1691,
by Leibniz,
Huygens and
Johann Bernoulli,
in their respective responses to an open challenge from
Jakob Bernoulli.
The Catenary
- Mathematics all around us, by James Grime (singingbanana).
|
Wikipedia :Catenary
(2015-02-15) Tractrix (Huygens, 1692)
It's at a constant distance a from its asymptote along the tangent.
The surface generated by revolving the tractrix about its asymptote
is known as the tractricoid.
It has a finite surface area of 4pa 2
and it encloses a finite volume of
2/3 pa 3.
The tratricoid is a surface of constant negative
Gaussian curvature.
Such a surface is known as a pseudosphere
and provides a concrete model for the hyperbolic geometry
first described axiomatically (negating Euclid's fifth postulate)
by Lobachevsky and Bolay (Beltrami, 1868).
The witch of Agnesi.
Agnesi's cubic (versiera).
[French: agnésienne]
[Spanish: bruja de Agnesi]
The curve's cartesian equation is:
y = a3 / (x2+a2 ).
It's associated with a circle of diameter a
tangent to the x-axis at the origin O.
A point M on this curve may be obtained via a line OPQ where P is on the circle
and Q is at height a; M has the x-coordinate of Q and the y-coordinate of P.
It seems you've got to be about 30 years of age to be interested in this...
The Italian name versiera (used by Agnesi) was actually given to the curve by
Grandi in 1718, because of the "inverted sine" (sinus versus)
which is used in its construction.
In spite of what is often stated, there may not be any direct relation
with the Latin word versoria which denotes the rope used
on a sailboat to transfer edge (the verb vertere means "to turn").
The weird name of "witch" comes from a famous mistranslation
by the Lucasian professor of mathematics at Cambridge, John Colson (1680-1760).
When he translated Maria Agnesi's Istituzioni Analitiche
[written in 1748, this was the first calculus book ever authored by a woman]
Colson apparently mistook "la versiera" for "l'avversaria"...
Since l'avversario (the adversary) is the Devil,
an avversaria would be a she-devil, or a witch!
Colson's work seems also responsible for the attribution of the curve to Agnesi
(she made no such claim herself).
The area between the versiera and its asymptote [the x-axis]
is pa2,
which happens to be exactly 4 times the area of the associated circle.
The function
a / p(x2+a2 )
thus corresponds to the density of a continuous probability distribution
(whose standard deviation is infinite ).
(2004-06-23) Folium of Descartes (1638)
Its cartesian equation is:
x 3 + y 3 = 3axy
The asymptote is of equation:
x + y + a = 0
The surface area of the lobe is 3 a 2/ 2
. So is the area between the asymptote and the curve.
The total signed area bounded by the
oriented closed loop consisting of the folium and its asymptote
is zero (that loop is understood to include 2 points
"at infinity"
and to have a continuous tangent vector at the double point).
(2004-06-21) Lemniscate of Bernoulli
The Latin word "lemniscus" means pendant ribbon.
This name was first used in 1694 by
Jacob Bernoulli (1655-1705)
to describe the above planar curve, which is now named after him.
A lemniscate of Bernoulli is the particular
Cassinian oval which goes through the
midpoint between its foci.
If 2a is the distance between the foci,
the lemniscate's cartesian equation in the proper coordinate system is:
( x 2 + y 2 ) 2 =
2 a 2 ( x 2 - y 2 )
The horizontal width of the curve is 2Ö2 a,
while its height (or vertical width) is simply a.
The surface area of each lobe happens to be simply a2.
(2004-06-21) Ovals of Cassini
/ Cassinian Ovals
/ Cassini Ovals
Cassini ovals are planar curves along which the product of the
distances to two given points, called foci, is a constant
[ foci, plural of focus, is pronounced "foe-sigh"].
By contrast, the sum
of these two distances is a constant along an ellipse...
Generalized Definition of a Cassini Ovum :
A multipolar Cassini ovum can be defined as the set of all
points whose distances to a certain number of fixed poles
have a constant product.
In the plane, such sets are curves (circles in the monopolar case,
traditional ovals of Cassini in the dipolar case).
In 3-dimensional Euclidean space, they are 2-dimensional surfaces
(possessing cylindrical symmetry in the dipolar case only).
A Cassini ovum in higher dimensions is an hypersurface.
The above generalized definition isn't universally accepted.
It's prudent to restate it before use, possibly with a link to this note:
These curves are named after
Etienne
Pascal (1588-1651), the father of the French scientist and
philosopher Blaise Pascal (1623-1662).
Etienne Pascal was part of a circle of mathematicians who held weekly meeting in Paris,
around Marin Mersenne (1588-1648).
This famous mathematical group included
the likes of
Pierre Hérigone (1580-1643),
Claude Mydorge (1585-1647),
Girard Desargues (1591-1661),
Pierre Gassendi (1592-1655),
Jean Beaugrand (1595-1640),
René Descartes (1596-1650),
Claude Hardy (1598-1678),
Pierre de Carcavi (1600-1684)
and also Gilles Personne de Roberval (1602-1675)
who is the one who actually named the limaçon after Etienne Pascal
in 1650, when he used it as an example for the drawing of tangents.
A limaçon can probably be defined in more different ways
than any other quartic curve.
It can be described in any of the following equivalent ways:
Curve of polar equation
r = a cos(q) + b
Curve of cartesian equation
( x 2 + y 2 - ax ) 2
= b 2 (x 2 + y 2 )
Epitrochoid of unit ratio, namely:
The trajectory of a point at a distance ½ a from the center
of a circle of diameter b which rolls on a fixed circle of the same size.
This is called a unit epicycloid if a = b
(cardioid).
Conchoid of a circle (of diameter a) with respect
to one of its points.
In general, the conchoid of a curve of polar equation
r = f (q)
is the curve of polar equation
r = f (q) ±
b.
Here,
r = a cos(q)
is indeed the polar equation of a circle of diameter a
which goes through the origin.
Pedal curve of a circle of radius b with respect to a pole
at a distance a from its center.
In general, the pedal of a curve is the locus of the foot of the perpendicular
from the pole to a tangent of the curve.
Inverse of a conical section with respect to one if its foci.
Envelope of the circles centered on a fixed circle and containing a given point.
Etc.
A cardioid is a limaçon
for which a = b.
A circle is obtained for b = 0.
(2004-06-22) Cartesian Ovals / Ovum of Descartes
Given two poles A and B, a cartesian oval is the set of all points
M for which AM + l BM
is a constant (for some fixed parameter l).
This three-parameter family of curves includes the
above [two-parameter] limaçons of Pascal
as a special case (corresponding to the cartesian ovals which go through a pole).
(2012-11-18) Envelope of a parametrized family of curves
At every point, the envelope is tangent to a curve from the family.
If the cartesian equation of each curve is F(x,y,t) = 0
for a fixed value of the continuous parameter t, then the equation
of the envelope is obtained by eliminating t between the two equations:
(2012-11-20) Involute of a smooth curve
(French: développante )
Trajectory of a point on a line that rolls (without sliding) on the curve.
A concept due to Huygens (1673).
The normals of the involute are tangent to the curve.
A smooth curve is an involute of its evolute.
The involute can also be envisioned as the trajectory of the extremity of a taut string that is
wound onto (or unwound from) the curve.
If you must, use this latter viewpoint piecewise for
parts of the curve whose curvature has a constant sign.
There's no mathematical difficulty when the curve crosses its tangent, but then it can't
really be viewed as the perimeter of an actual spool of string.
Of particular interest is the involute of a circle (which is what
the term "involute" is understood to denote when it doesn't come with a qualifier).
This is the onlytooth profile that
makes a driven spur gear rotate at a uniform rate
(or "steady speed") when the driver does.
All other types of spur gear will thus induce systematic vibration that
are unacceptable for high-speed heavy machinery
(but perfectly fine for low-speed clockwork in which pulsed rotation is the norm).
(2009-02-21) Parallel Curves (Leibniz, 1692)
Two curves which stay at a constant distance (locally).
The envelope of the circles of radius a centered on a curve
G is generated by the two points at distance a
on the normal to G at a running point P.
For a simple closed curve, this envelope can be divided into two separate curves;
the inner and outter parallel at offset a,
which are respectively generated by the points on the normal which lay on
the inward or outward side of the normal.
(In the field of computer graphics, parallel cfrom each other by translation.
The perimeters of a smooth closed curve and that of one of its
[single-sided] parallels at offset a have either a sum or
a difference equal to 2pa.
(2009-11-22) Nephroid, two-cusped epicycloid (1678)
Point on the circumference of a disk rolling outside a circle twice as big.
This curve was introduced in 1678 as the catacaustic
of a circle by Christiaan
Huyghens (1629-1695) who would later
discuss it in Traité de la lumière (1690).
The term nephroid was coined by the English astronomer
Richard A. Proctor (1837-1888)
in The Geometry of Cycloids (London, 1878).
x = a ( 3 cos t - cos 3t )
y = a ( 3 sin t - sin 3t )
(2005-06-01) Bézier Curves
Standard parametric curves used to approximate other curves.
Bézier curves are often restricted to planar geometry, but they need not be.
Pierre Bézier
(1910-1999)
served as an engineer for the French car manufacturer Renault for 42 years,
from 1933 to 1975. He was also a professor at the
Conservatoire national des arts et métiers
(CNAM) from 1968 to 1979.
He introduced the type of curves now named after him
for "free-form curves" within the CAD/CAM system dubbed UNISURF, which he launched in 1968.
The order-n Bézier curve from P0 to Pn
involves n+1 control points (Pi ).
A point M(t) of the curve is the following barycenter of the control points:
M(t) =
n
å
i = 0
æ è
n i
ö ø
t i (1-t) n-i Pi
Unless otherwise specified, order n = 3 is understood,
in which case alternate names may be used:
"Bézier cubic", "cubic spline" (or just "spline").
Such a curve is given by its extremities A and B and two other control points P and Q:
M(t) =
(1-t) 3 A
+
3 t (1-t) 2 P
+
3 t 2 (1-t) Q
+
t 3 B
As t goes from 0 to 1, M(t) goes from A to B. Assuming distinct control points,
the line AP
is tangent to the spline at point A, whereas BQ is the tangent at point B.
It's good to know that if PQ is parallel to AB and
PQ = AB/3, then the Bézier cubic spline is actually a
parabolic arc.
Thus, it's easy to obtain parabolas from any computer graphic package that provides
Bézier cubics (most of them do).
Bézier curves of order 2 (with a single intermediary control point R)
correspond to these same parabolic arcs,
since the relations P = (A+2R)/3 and
Q = (2R+B)/3 imply:
(1-t) 3 A
+
3 t (1-t) 2 P
+
3 t 2 (1-t) Q
+
t 3 B
=
(1-t) 2 A
+
2 t (1-t) R
+
t 2 B
Any Bézier curve of order n (with control points
Pi ) is also a Bézier curve of order n+1 with
control points Qi given by the following relation.
Note that:
Q0 = P0 and
Qn+1 = Pn
[HINT: Expand (1-t) M(t) + t M(t) ]
æ è
n +1 i
ö ø
Qi =
æ è
n i -1
ö ø
Pi-1 +
æ è
n i
ö ø
Pi
Pascal's formula makes this a
barycentric relation:
Qi is between
Pi-1 and Pi
(e.g., in the above parabolic-to-cubic case, P is on AR and Q is on RB).
Dr. Nicholas A. Sceusa (2005-05-29; e-mail)
Piecewise Circular Curves
How may an approximation to an arbitrary curve be constructed
using only compass and straightedge?
[Without neusis.]
In the computer era, the most popular approximations for arbitrary curves
involve algebraic splines, like the Bézier curves
discussed above.
For more traditional work, the circle remains, indeed, the basic curve of choice.
The following procedure assumes that the curve we want to approximate
contains no straight sections and no angular points
(otherwise we'd process separately each piece of the curve between these).
To build a smooth curve consisting of circular arcs which approximates the original curve,
we first choose a number of "construction points" located on that
curve. If the curve is open, we must include its extremities among these.
It's also a good idea to include
any inflection points the original curve may have.
(Inflection points are points where the curve crosses its own tangent.
Near one of its inflection points, the curve is usually very close to a straight line.)
Draw the tangent to the curve at each construction point.
Join two consecutive construction points by a circular arc centered at the
point where the perpendiculars to the relevant tangents intersect.
Such lines always intersect if all inflections points have been included among
the construction points; parallelism would indicate that we're bracketing
an inflection point and need more intermediary construction points.
(A practical alternative is to "cheat" by introducing small straight sections
around inflection points.)
The intrinsic equation of a piecewise circular function
is a step function...
(2005-06-06) Planar Shape: Intrinsic Equation of a Planar Curve
Defining a shape by its curvature,
as a function of curvilinear abcissa.
The curvilinear abscissa (often denoted s) is the arc length
measured along the curve from some arbitrary origin on it
(counted negatively "before" this origin).
At a particular point, the curvature
of a planar curve has a magnitude equal to
the reciprocal of its radius of curvature
(the radius of the so-called osculating circle
which best approximates the curve in the immediate neighborhood).
By convention,
the sign of the curvature is positive
if the curves turns to the left
of the direction of an increasing curvilinear abscissa.
The curvature is zero at an inflection point, or at any point of a straight section.
The so-called intrinsic equation (which gives the curvature
of the curve as a function of the curvilinear abscissa along it)
uniquely defines the "absolute" shape of a planar curve
(it could be translated or rotated, but not flipped over).
Infinite curvature: "Planar shapes" are distributions
The above viewpoint is only adequate for smooth curves with no angular points. However,
it's easy to generalize it to angular curves, since the curvature is
the derivative [with respect to curvilinear abscissa] of the angle (in radians)
between some fixed direction and the tangent to the curve.
A sharp turn of q radians at a point
so of infinite
curvature thus translates into a Dirac spike
q d(s-so)
in the intrinsic equation (namely,
a Delta distribution
of amplitude q ).
Dr. Nicholas A. Sceusa (2005-05-31; postal mail)
On the Quadratrix (or Trisectrix) of Hippias
Could Hippias
draw his quadratrix with straightedge and compass?
The quadratrix is the trajectory of the intersection of two straight lines:
One in uniform motion, the other uniformly rotating about a fixed point A.
Infinitely many constructible
angles can be used to obtain points of the quadratrix.
In particular, as any angle can be bissected with straightedge and compass,
we may divide a circle in 2, 4, 8, 16, 32, 64...
2 n equal angles.
Draw such radial lines for a sufficiently large n, then
draw any set of equally-spaced parallel lines.
The points where successive radial lines intersect successive
parallel lines are on a quadratrix...
(Intermediary points may be obtained by doubling up the lines in both sets.)
The ancient Greeks only considered those points which could be
deduced from a few given points in finitely many uses of
a straightedge or a compass.
The quadratrix of Hippias was the first curve on record whose points
cannot all be so deduced.
Thus, it's not considered a constructible curve,
although infinitely many points on it can be constructed classically, as shown above.
In the proper coordinate system, the cartesian equation of the quadratrix is:
y = a - x / tan(x/a)
The center of rotation (A) is at (x,y) = (0,a).
The curve's apex (O) is at (0,0).
The main branch is bounded by two vertical asymptotes
(-p < x/a < p)
and corresponds to a full turn of the rotating line.
Only the central portion is usually considered
(-p/2 < x/a < p/2)
which corresponds to a half-turn of the rotating line, between horizontal positions.
The portion where x is positive may suffice.
The curve was devised around 420 BC by
Hippias of Elis.
It's been called either quadratrix or trisectrix
because it provides graphic solutions to two famous classical problems,
which are now known to be
outside the scope of what can be done with straightedge and compass:
The squaring (quadrature) of the circle and the trisection
of an arbitrary angle.
Also,
Heath
has attributed to
Archytas
of Tarentum
a "quadratrix solution" to the third most famous classical problem of this kind,
the duplication of the cube, or Delian problem.
Legend has it that the Delian problem dates back to 430 BC,
when the Oracle of Apollo at Delos said the plague ravaging Athens would come to
an end if the altar of Appollo could be made exactly "twice as large"
[by volume].
The cube root of 2 is still occasionally known as the
Delian constant.
The quadratrix can be used to "square the circle" because the number
p (which can't be constructed with straightedge and compass)
is simply obtained as the ratio of the width to the height of the section of
the quadrarix whose extremities are on an horizontal line through A.
To obtain a portion l of an arbitrary angle
(including l = 1/3) whose vertex is at point A,
consider the two points where its sides intersect the main branch of
the quadratrix.
Draw trough them 2 lines parallel to the axis of the quadratrix.
If M is the point where the quadratrix intersects a third
parallel line dividing the space between them
in the ratio l, then
the line AM divides our angle in the ratio l.
This wonderful curve is thus directly related to yet another famous problem:
the construction of an n-sided regular polygon.
Equilateral triangles, squares, regular pentagons and hexagons are all
constructible with straightedge and compass, but it turns out that
regular heptagons, enneagons,
hendecagons, or tridecagons cannot be so obtained.
This was established in 1796 by Carl Gauss (at age 19) who showed the heptadecagon
(17 sides) to be classically
constructible.
(2005-06-06) A Parabola is an Example of a Constructible Curve
Locating any point on a parabola, with only straightedge and compass.
A parabola is the set of all points of the plane at an equal distance from
a given point (called the parabola's focus)
and a given line (the parabola's directrix).
The parabola is called "constructible" because its intersection with
an arbitrary straight line, or an arbitrary
circle, can always be
located in finitely many steps using only straightedge and compass.
Thus, allowing the use of of a parabolic spline in addition to straightedge and
compass would not introduce any additional "constructible" points.
This could make classical geometry easier, but not richer.
(2005-06-20) The Mohr-Mascheroni Theorem:
All constructible points can be obtained with the compass alone.
This statement about classical planar geometry used to be credited to
Lorenzo
Mascheroni (1750-1800) who proved it in
Geometria del compasso (1797).
However, 125 years earlier, the Danish mathematician
Georg
Mohr (1640-1697) had published anonymously a book entitled
Euclides Danicus (1672)
which contains a prior proof...
This was completely overlooked until 1928, when a copy of that little-known work
surfaced in a bookstore
(there's no record of any copy ever sold before then).
Classical constructions which avoid the use of a straightedge are
thus now best called
Mohr-Mascheroni
constructions.
Georg Mohr had also shown that all Euclidean
constructions could be done with only a straightedge,
if a circle of given center is already drawn somewhere in the plane.
The Swiss mathematician Jakob Steiner (1796-1863)
rediscovered this in 1833 (Steiner constructions).
We may prove that all constructible points can be obtained
with the compass alone by providing Mohr-Mascheroni constructions
for the two types of points which normally involve the use of the straightedge:
The intersections of a straight line and a circle.
The intersection of two straight lines.
We'll do so using only two explicit Mohr-Mascheroni constructions,
concerning the inversion with respect to a circle and
the circumcenter of three points.
The very simple construction we'll provide for the former isn't completely
general unless supplemented by a scaling-up procedure, like the following one:
Doubling up, with the compass alone :
An example of a Mohr-Mascheroni construction is the
doubling, which we'll use below:
Given two points O and M, the point N in the direction of OM
such that ON = 2OM may be obtained as follows:
Draw the entire circle (C) of center M and radius OM.
It intersects the circle of center O and radius OM at points A and B.
The circle of center A through B (or center B through A) intersects (C)
at point N
(It wouldn't be acceptable to define N as the intersection of the circles
centered on A and B, because there are two
such points of intersection, both "new".)
Inversion of the plane, with respect
to a circle :
The so-called inversion of the Euclidean plane
with respect to a circle of center O and radius R
is a transformation which was introduced in 1826 by
Steiner
(in his first published paper).
The inverse of a point M (other than O)
is the point N in the direction of OM which is such that
OM.ON = R2.
This transforms a circle through O into a straight line,
and vice-versa.
Circles not containing O are simply associated with other such circles.
N is very simple to obtain from M with the compass alone:
Assume OM is more than R/2 and consider the intersections A and B
of the invariant circle
with the circle of center M and radius OM.
Let N be the intersection (besides O) of the circles of centers A and B
going through O. We have:
OM . ON = R 2
This relation is easy to prove
with cartesian coordinates: O=(0,0), A=(x,y), N=(2x,0), M=(a,0).
Since, R=OA and MO=MA, we have:
R2 = x2 +
y2 and
a2 = (a-x)2 +
y2. By subtraction:
R2 = 2xa = OM.ON
If OM is R/2 or less, we may first obtain a point M' such that
OM' = 2n OM, using the above
doubling n times, for a value of
n large enough to make OM' greater than R/2.
The inverse N' of M' is then constructed as above.
Finally, the inverse N of M is simply obtained by
doubling ON' n times.
Circumcenter of 3 given points :
The construction,
with straightedge and compass of the center of the circle circumscribed to
a triangle is a very
early piece of mathematics;
the circumcenter of a triangle is
the intersection of the perpendicular bissectors of two sides.
The following Mohr-Mascheroni construction uses an inversion centered
on one of the 3 vertices to obtain the inverse of the circumcenter
as the intersection of the two circles which are inverses of these bissectors.
Consider a triangle ABC, whose circumcenter N is sought.
In an inversion of center A and radius AB, the image of the perpendicular
bissector of AB is a circle U of center B and radius AB.
On the other hand, the inverse [with respect to the circle U]
of the perpendicular bissector of AC is
a circle V of diameter AH', where H'
the inverse of the middle H of AC.
The center of V is thus the inverse C' of C
(constructed as indicated above).
The circles (U and V) through O of centers B and C' intersect at another
point M, whose inverse (with respect to U) is the circumcenter N of ABC
Of course, once the circumcenter is thus obtained, with compass alone,
the entire circle through A, B and C is easily drawn...
Doing away with the straightedge entirely:
In classical geometry, any planar figure
consists of straight lines and circles:
A straight line is given by two of its points.
A circle is given by its center and a point on its circumference.
It may also be defined by 3 points on its circumference
(Euphorbus).
Consider an inversion
of radius R whose center O is distinct
from the finitely many points of intersection of such a classical figure
(it's best to let the distance of O to all such points be between R/2
and R so the simplest compass construction can be used to go back and
forth between a point and its image):
The inverse of the straight line trough the points A and B is the circle
going through O and the respective inverses A' and B'
of A and B.
The inverse of the circle through A, B and C is the circle going
through their inverses A', B' and C'.
These remarks and the above explicit compass-only constructions
allow the inverse of all the elements of a Euclidean planar figure
to be drawn with compass alone.
The intersections of such elements can be constructed
with compass alone as the inverses of the intersections in
the inversed figure.
(2020-06-14) Osculating curves
The Tait-Kneser theorem and its beautiful extensions.
(2004-06-23) Confocal Conics
This famous mathematical group included
the likes of
Pierre Hérigone (1580-1643),
Claude Mydorge (1585-1647),
Girard Desargues (1591-1661),
Pierre Gassendi (1592-1655),
Jean Beaugrand (1595-1640),
René Descartes (1596-1650),
Claude Hardy (1598-1678),
Pierre de Carcavi (1600-1684)
and also Gilles Personne de Roberval (1602-1675)
who is the one who actually named the limaçon after Etienne Pascal
in 1650, when he used it as an example for the drawing of tangents.
correspond to these same parabolic arcs,
since the relations
